March 2014 - Misc. Wanted

All Classified Ads

Aircraft drop tank wanted; Charlie Parish nnn-nnn-nnnn (Merced CA)

Boring bars for a 3 bar boring tool holder wanted. Sizes I need are 3/4 and 1-1/8" with square tool bit holes. Good US quality, please, Armstrong, Williams, etc; Robert Anderson nnn-nnn-nnnn (Kearny AZ)

Combine wanted: John Deere Pull type complete preferred any: Mark Parker nnn-nnn-nnnn (Lebanon OR)

Cutter-bar lifting arm for a John Deere M-20 center mounted mower wanted. This is a cast iron part with the JD part number of AZ 3474H; Dick Deschamps nnn-nnn-nnnn or xxxx@xxxx.xxx (Bozeman MT)

John Deere remote hydraulic implement cylinder wanted for my John Deere KBA disk, 44H plow etc. Good working condition or rebuildable. No breaks, cracks or welds. Shaft straight and smooth; Larry Pestes nnn-nnn-nnnn (Boring OR)

Line shaft parts wanted: Flat belt drive pulley. Step pulley takes a 1-3/4” wide belt, with (3) steps of 3”, 4 1/2”, 6” in diameter. I am also looking for line shaft hangers, clutches, shafting, etc; Greg Fosmark nnn-nnn-nnnn or xxxx@xxxx.xxx (Issaquah WA)

Old arbor press wanted, good US quality in working condition; Robert Anderson nnn-nnn-nnnn (Kearny AZ)

Old cross slide table wanted, to be used on a large drill press. Must have X and Y travel, good US quality; Robert Anderson nnn-nnn-nnnn (Kearny AZ)

Old mining equipment, small oil derrick, etc wanted; Larry Daniels nnn-nnn-nnnn (Phelan CA)

Old steel wheeled wagons/carts with saws, crushers pumps etc wanted; Larry Daniels nnn-nnn-nnnn (Phelan CA)

One-row corn picker wanted, must be in working condition; Daniel M. Thompson nnn-nnn-nnnn or xxxx@xxxx.xxx (Winnemucca NV)

Plow shares & shins for John Deere Model 44 plow wanted: shares # B.C 217, need 3; shins #V 290 A, need 3; Philip S. Robustellini nnn-nnn-nnnn or cell nnn-nnn-nnnn or farmallf12 @att.net (Montague CA)

Plow wanted: John Deere model 666 or 777, 4, 5 or 6 bottom, any condition; Mark Parker nnn-nnn-nnnn (Lebanon OR)

Tires wanted: 13x24 grader tires wanted; Charlie nnn-nnn-nnnn (Yakima WA)

Trailer wanted: Single axle low-boy trailer wanted; Charlie nnn-nnn-nnnn (Yakima WA)

Wanted: Early Scooters: Tote Goats, Cushmans, Valiants, Rose Ramblers, other makes & models; Buck nnn-nnn-nnnn or nnn-nnn-nnnn (Ellensburg WA)

Wanted: Lathe driving dogs wanted. Bent tail type. Good US quality. Armstrong, Williams, etc, must be in usable condition. Sizes needed: 1-7/8", 2", 2-1/8", 2-3/8', 2-1/2", 2-7/8", 3", 3-1/4", 3-3/8", 3-1/2", 3-5/8", 3-3/4", 4". Old dogs were available in these sizes. Will take what is available. Also want outside jaws for a buck chuck, adjust true 3 jaw with a buck part # 4831. This is an 8-1/4" chuck. Need lathe chuck threaded back plates, 2-1/2" spindle, 6 threads per inch, 2-5/8" spindle, 6 threads per inch; Robert Anderson nnn-nnn-nnnn (Kearny AZ)

Wanted: old advertising signs of any type advertising oil, gas, tractors, bread, soda pop, milk, bread, etc, made of enamel, tin or cardboard. Also want old gas pump, old slot machines, vending machines, cigarette, soda pop, old amusement park games, rides etc, working or not; Joe Giordano nnn-nnn-nnnn or xxxx@xxxx.xxx (Port Orchard WA)

Would like information on this military type cart. Measures 27" wide X 52" long X 5" deep. Has 19" wheels with 4:00 tires, camo cover and leather belting & tie-downs. Has metal tag reading: "Eidgenussische Konstruktions-Werkst???? THUN No 19567 1938"; Jim nnn-nnn-nnnn (Benton CA)