October 2013 - Tractors & Parts Wanted

All Classified Ads

Allis Chalmers M, 1940, needs fuel tank & exhaust & intake manifold; Ken Boyd nnn-nnn-nnnn (Livermore CA)

Best Sixty Tracklayer parts wanted. I am looking for a radiator, valve covers, undercarriage parts, and a few other miscellaneous pieces to build my Best Sixty. Any parts leads appreciated; Mr. Kim Kestler nnn-nnn-nnnn (Reno NV)

Best Thirty tractor wanted. Looking for a Best thirty tractor, any condition, whole or parts; Mr. Kim Kestler nnn-nnn-nnnn (Reno NV)

Bombardier tracks for Ford 8N wanted; Dennis McClain nnn-nnn-nnnn (Redwood Valley CA)

BUDA headless 4cyl engine, mods. R, RU, W or WU 3.5"-3.75" bore wanted; Roland nnn-nnn-nnnn (Grants Pass OR)

Cleveland Tractor (early Cletrac) model "R" parts book or operators/instruction manual wanted; Roland nnn-nnn-nnnn (Grants Pass OR)

Drum pulley wanted for the PTO unit on a 1948 CJ2A Jeep. It is the pulley that a wide belt would have been slid over to run implements off the rear PTO of a Jeep; Don Masters nnn-nnn-nnnn or xxxx@xxxx.xxx (Redmond WA)

Farmall 100 engine or block without cracks needed. Oliver 77 or Super 77 parts tractor needed must have good condition rear casting and internals - can be 77, Super 77 or 770. One of my Olivers' final drive housing cracked side to side. I am a vegetable farmer and these are for putting back into service on my farm; Grant Brians nnn-nnn-nnnn or nnn-nnn-nnnn (Hollister CA)

Farmall Cub front blade wanted, whole thing or just the operating/mounting brackets; Bob Stere nnn-nnn-nnnn or xxxx@xxxx.xxx (Hillsboro OR)

Ferguson Transport Box tailgate. The gate is part # T-JO-60 for the T-JO-20 Transport Box. Also need hook for locking to lift arm, part #T-JO-8800. Would like parts in good to restore-able condition; Jon Rodgers nnn-nnn-nnnn (Sonora CA)

Flat belt pulley & gear box for a 1948 D4 Cat wanted; Tracy Moch nnn-nnn-nnnn (Braddock ND)

Ford 8N cast aluminum rear hood extension used on a 6 cyl Funk Conversion wanted (this would fit just forward of the steering wheel); Norm Keesler nnn-nnn-nnnn or e-mail xxxx@xxxx.xxx (Nampa ID)

Fordson flat belt pulley wanted in usable condition, just need the paper pulley; George Best nnn-nnn-nnnn or xxxx@xxxx.xxx (Beaverton OR)

IHC BD-240 exhaust manifold wanted; Dave Webb nnn-nnn-nnnn (Scotia CA)

International Cub LoBoy attachments wanted; Warren Harger nnn-nnn-nnnn (Central Point OR)

John Deere 145 loader with 5 or 6 foot bucket wanted for my John Deere 1530; Chris nnn-nnn-nnnn

John Deere 420 or 430 crawler wanted; nnn-nnn-nnnn or xxxx@xxxx.xxx (Beavercreek OR)

John Deere GP orchard tractor, GPO wanted. ANY year, ANY condition. Also looking for a GPWT, GP wide tread tractor you might have or know of for sale. Thank you; Eric Burke nnn-nnn-nnnn or xxxx@xxxx.xxx (Washington IL)

Looking for distillate manifold for 1936 T20 crawler, same as F20 tractor, will consider any parts

available for T20; Kevin Wheeler nnn-nnn-nnnn or xxxx@xxxx.xxx (Sudbury MA)

Massey Ferguson 50 needs seat, lower nose cone & grill; Dennis McClain nnn-nnn-nnnn (Redwood Valley CA)

Massey Harris 81 needs sheet metal & misc parts; Ken Boyd nnn-nnn-nnnn (Livermore CA)

Small 30-50 hp tractor wanted, like Ford 3000 or 4000, International or Kubota; Doug Black nnn-nnn-nnnn (Atwater CA)

Tracks for Cleveland tractor model H crawler wanted, early narrow type; Roland Bleitz nnn-nnn-nnnn (Grants Pass OR)

Tracks for early Cleveland Tractor crawler, 6"- 6.5" wide wanted; Roland Bleitz nnn-nnn-nnnn (Grants Pass OR) [link to photo]

Wanted: Center mount blade & wheel weights for IH Farmall Cub tractor; Del Hollingsworth nnn-nnn-nnnn (Albany OR)