Are You Attending the Tulare, California Show April 16-17-18? Again I am bringing my trailer full of manuals and sales literature but as usual I cannot bring it all. If you need me to bring something in particular, feel free to contact me. Jim Robinett, 5141 Kimball Rd., Ontario, OR 97914 or 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Allis Chalmers B, 1939, good paint & rubber, runs good, $1000; Rich Dorn 951-532-5270 (Mira Loma CA)
Allis Chalmers B, 1941, good paint, good sheet metal, runs good, $795; Al Norwood 760-347-6462 (Indio CA)
Allis Chalmers B, 1952, sn B120609. Engine totally rebuilt new liners and pistons, turned crank, valve job including new exhaust seats. Clutch rebuilt, new release bearing, resurfaced flywheel. New water pump, rebuilt starter, rebuilt generator, 12 volt, new regulator, new solenoid. Sheet metal is straight, would love to be repainted. Front tires are like new, rear are very good. Hydraulic works. Rear blade and original front saddle weights included. Approximately 100 hours since rebuild runs like new, $2500; Jim Temple 541-935-7567(Noti OR)
Allis Chalmers B, approx 1957. Has auxiliary transmission & hydraulics, new rear tires, $1500; Ed Bring eves, 503-829-8528 (Molalla OR)
Allis Chalmers CA, early 1950's. Tractor has been cosmetically restored. It is in working condition and runs well. Could benefit from some top end work if were to be used as field tractor. A local tractor enthusiast who works on them in his spare time restored this. He did a wonderful job. Asking $3000 or best offer. Please email me for pictures and more info; Clinton Paulson 585-410-2152 or capauls29@hotmail.com (Bath NY)
Allis Chalmers G parts: Complete Master hand lift, Master tool carrier, Rear furrowing bar. Also lots of engine, transmission, and wheel parts just in. Email for photos. John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
Allis Chalmers HD-5, dozer, canopy, winch, excellent, $4250; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers HD-7 farm cat with cab, 371 Detroit, $1500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers K, has blade, winch, canopy, restore? $2100; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers W Road Patrol, good shape, rare, $5250; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers WD45 diesel, all original with a Buddha engine. Runs excellent, has good oil pressure, two wheel narrow front end, CO-OP rear tires, front tires are new, working two point, power steering, $3800; Lonnie Rollins 541-415-0097 or labbr@frontiernet.net (Cave Junction OR)
Allis Chamers C, 1948, runs, needs battery, $1300; Rich Dorn 951-532-5270 (Mira Loma CA)
Allis Chalmers WD, 1952. Mostly restored, new epoxy paint, tires 100%, 3-point hitch, lots of new or NOS parts. Rear dirt scoop, boom pole, rear blade. Used for show and plowing snow. Includes books and some extra parts. Fun to drive in parades. Can e-mail photos. $3,200; Tom Lyman 208-660-3089 or tomlyman@hotmail.com (Post Falls ID)
Baker valve for John Deere power lift, $275; Gary Jondle 360-379-8438 (Port Townsend WA)
Belt pulley assembly for Oliver 60, $200. Email for photos; John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
Case C, 1929 on steel, flat fan belt, restored, $3750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Case C, have two 1929's, both are complete and stuck on cutdowns to rubber. 1 has rare flat belt water pump and 1 set of rear steel. Package deal, $1650 obo; Mark Parker 541-619-2692 (Lebanon OR)
Case DI, 1945, parting out or for restore, call for details, $200; Lon Sisson 707-548-6399 or 707-829-8785 (Sebastopol CA)
Case parts: Hood, grille & other Misc. sheet metal parts for some sort of Case "Tripl-Range" Tractor. Call for details; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Case RC, 1936, restored, new rubber, paint, $3750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Case tractor parts for old V, S & D series; Steve Stevens 509-995-4627 (Medical Lake WA)
Caterpillar 10, runs, steers good, has engine side panels, $3000; Bob Smythe 503-257-9615 (Rhododendron OR)
Caterpillar 15 (small), 7C series, 1932. Excellent running condition, always stored under cover. Picture available, $7500; Melody Hemley 253-853-6438 or cell 360-801-1240 (Port Orchard WA)
Caterpillar 20, Big 20, have two to restore, $3000 & $2000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 20/25/28 PTO complete, reduced to $350; Cat 20/25/28 radiator grill, $150; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 22 orchard fenders, 1 pair, $200; Paul Hadden 760-329-7657 (Desert Hot Springs CA)
Caterpillar 22 parts: belt pulleys, choice, both loose, complete, metal cast pulley or conventional, $500 each; Cat 22 Zenith K5 Propane carb complete with spare gas Zenith carb, $200; Cat 22 Zenith K5 carbs complete, two carbs, $175; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 22 wide gauge top seat with 8' 4 gang disc. Runs good with many new parts, $4000; Wally Adams 408-268-3308 (Morgan Hill CA)
Caterpillar 22 with hydraulic dozer and electric start, 1936 mfg. Runs perfect. Newly recovered seat and backrest. No rust. Ops and overhaul manuals, $3500; Byron Henning 559-683-7547 (Oakhurst CA)
Caterpillar 22, citrus orchard with Bishop fenders, $2500; Caterpillar 22 engine, very nice, $950; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 22, wide gauge running tractor. Pretty darn good undercarriage with rails that appear to be 75% or more with beefy sprockets. Grousers are 1.375 to 1.5". Still has original Cat decals viewable on hood and fuel tank. Modest hitch pin wear. Runs 20 psi oil pressure at idle. Think mag needs a rebuild as the tractor runs fine from idle to a bit over half throttle and as you provide more throttle (past half) the tractor starts sputtering. $2750. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30 on propane, will run with a little work. Tracks and undercarriage are in very good condition. S/N s9016, has belt pulley on rear. $2500 or offer. Can E-mail photos to serious buyers; Dax Kimmelshue 530-345-4456 or daxandkaren@yahoo.com (Durham CA)
Caterpillar 30G wide-gauge factory electric start. Tractor runs and drives very well. Tractor has rebuilt top end, great manifolds, rebuilt electric starter. CM4 magneto, lights, factory nose-guard, mushroom air-breather. Very straight tractor which is unrestored. Can provide pictures. $7500 Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30G-R4 brand new old stock exhaust manifold with fins. Fabulous shape. Indescribably good, $1500. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30G-R4 intake manifold in very good shape (no drop tube), $450. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 35 diesel, bad final, otherwise good, $2750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 40 5G gas wide gauge, rare tractor, recent engine work, electric start, good undercarriage, runs & drives very well, new paint & seats very nice, $9500. Check our web site www.omnitrac.com. Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar 50, gas, complete, restorable, $5000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 5U wide gauge direct electric start large front idler toolbar dozer. Tractor runs and drives very well. Tractor had the top end gone through this winter with head shaved/trued, all new glow-plugs, All new injector nozzles, new gaskets, new thermostat, new main clutch. $2k in just new parts alone. New hydraulic hoses from factory metal lines to hydraulic rams. Factory PTO with belt pulley attachment. Belly pan (no hook). Tractor starts great hot or cold. Cat 44 single spool front mounted pump. Can provide more pictures. Extremely original. 158XX serial number. $10,000; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 60, complete, with blade, runs good, $10000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 60, powered by Ford. Runs and drives. It is a 223 Ford 6 motor & gets its power through the PTO. It's on the Cat 60 undercarriage; Randy Wixsten 406-494-5676 (Butte MT)
Caterpillar 60, sn 4914, very good undercarriage, new rings & valve grind, new fenders, rebuilt vacuum tank, rebuilt carb & mag, ID tags are intact on the rear housing, drives excellent, $16000. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar combine, early '30's, very restorable, $2500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D-2 5U, very nice, direct electric start, $6750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D2 belt pulley, $350; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar D2 J series: has four. One of the tractors are wide gauges and three are standard gauges. Four have the main engines loose. Asking $2500 for all five (actually 3.5 tractors) which is approaching scrap price but Rick is not a supporter of scrapping whole tractors and wants to sell to a party who may put one or more of the tractors to use in a restoration or as parts donors to another restoration; for details Rick Hawksworth 559-658-5711 or dunefrk@razzolink.com (Ahwahnee CA)
Caterpillar D4 7J, restorable, $1500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D4 belt pulley, $350; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar D4 parts: drawbar $15, fender $10, grill guard $10, sprocket assembly $15, loader bucket, $25; Ron 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar D6 seat tank $45. Good condition, photos available. Ron 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar D6 seat tank $45. Good condition, photos available; Ron Nevins 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar pads: wide 24" conventional pads for D4/R4/30/28. Rails ok, not special. 64 pads total with tall grouser height and little wear. Slight pitting in some pads as these came from the south, $1500. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar parts: 4S straight blade, complete with hydraulics off D47U, $2750. Canopy for D4, $750; Cat D47U four roller track rails, 95%, has pads, but pads only 50%, D4N winch, complete, very good, $1500; Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar parts: package D2/R2 guards, hydraulics, belly pan; I am packaging an R2/D2 Belly pan with a tow hook on it with a D2 hard nose-guard AND two cat 44 hydraulic pumps, 2 sets of lines from the pump to the cross-over pipe, two sets of cross-over pipes (fender to fender), two diverter values, one D2 mounting bracket, and one D2 pump to harmonic balancer coupling shaft. I think the pumps will need to be rebuilt. One does not turn currently. More discrete pictures available of the various parts. $1400. Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar RD 4, restorable, with tool bar blade, $1750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar straight blade for D25U, complete with Cat hydraulics $2200. One after-market tilt angle blade, complete, for D25J or D25U series $1200. Cat 2A angle dozer complete, $2500. Hyster D2N winch, complete, $1750. Check our web site www.omnitrac.com. Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar used parts for Cat 10, 15, 20, 22, 30, 40, 60, D2, D4, 2 Ton, D2, D4, JD Lindeman and JD crawlers, some TD6 and TD9 parts. Dozers, canopies, belly pans and winches. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar/Holt 2-ton sn 76028, good undercarriage, very straight, new paint & seats, original carb, drives very well, $6500. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar: Large selection of antique caterpillar tractors Cat 10 thru 60, some restored, some ready to restore. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Clamp-on 12X38 dual rims and all mounting hardware from JD 630 row crop no tires some surface rust lots of yellow paint please come get'em $100; Jim Temple 541-935-7567 (Noti OR)
Cletrac crawler, steers good, runs good, good undercarriage, older paint, $1500; Dick Good 541-619-6090 (Tangent OR)
Cletrac F, rare little tractor, circa 1921. In same family for over 40 years, was displayed in a renowned museum for most of that time. It is missing the starting crank and air box. But I have been told both of these items are not that difficult to come by. I have not run it, but it is free and has compression. It was put into the collection running. Call or email for photos. Valued at $12,000 to $15,000 but first $10,000 takes her home; Rick Limpp 406-670-7399 or oscarspark@bresnan.net (Billings MT)
Cletrac H, 1919, project, mostly complete, $1600; Jim McMullen 503-698-2313 (Clackamas OR)
Decals, NOS for Cub Cadet, Farmall, International, some Implements. Contact for needs, costs, S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Draw bar for Case 310F dozer/crawler. Good shape, $100; Tim Bynum 530-436-2593 or timandlaura@snowcrest.net (Yreka CA)
Estate sale: International Harvester W4, sn WBH18313WIA; Ford 8N's or 9N's (have six); Farmall Cubs (have 2); Allis Chalmers, International W4, sn WBH24804WI. Call and leave a message for more information or I can send pictures thru email; Patti 541-487-7198 or greendog03@hotmail.com (Alsea OR)
Farmall 300, straight sheet metal, single front, torque converter, hydraulic front & back, PTO, draw bar, excellent running condition, $2000; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall 300. Good sheet metal, wide front, torque converter, 3 pt hydraulic hitch, hyd front & back. Very good running condition, just needs paint, $2500; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall 350 side panels, center stirp; Mark Parker 541-619-2692 (Lebanon OR)
Farmall A, 1940, sn FFA33623, original and complete, excellent metal, all new rubber, engine is stuck after the winter freeze, $900 obo; Rick Siel 541-953-3465 (Eugene OR)
Farmall B, 1944, restored, very good condition, $2500; Lee Burnett 208-610-5871 (Sandpoint ID)
Farmall C, single front, good tin, runs good, has hydraulics; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall Cub 1949, new rings, valves and bearings. Good tires and fresh IH paint, hydraulics $2,350 with model 193 mounted plow and 28-A mounted disc. $2,000 without implements; Russ Shorten 509-382-8925 or cell 509-876-1795 (Dayton WA) [link to photo]
Farmall Cub misc parts; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Farmall Cub with sickle mower, $2500; Jerry Fischer 503-876-7921 (Willamina OR)
Farmall Cub, 1947, sold "as is" condition. Parts tractor or could be good runner with the right amount of work and time. 4-digit serial number 3154. Has no drawbar, generator, or front grille. Pictures available upon request, $600 obo; Jack Johnson 714-630 2912 or pd6pro@aol.com (Anaheim CA)
Farmall Cub, 1953, restored, with 5 ft sickle mower, very good condition, $2500; Lee Burnett 208-610-5871 (Sandpoint ID)
Farmall Cub, runs good, $1050; Dick Good 541-619-6090 (Tangent OR)
Farmall F12, 1936, w/mounted sickle mower, $500; Chris Mielke 909-223-0858 (Norco CA)
Farmall F-14 (124), restored. New rubber; Jim Farber 707-894-4759 eves (Yorkville CA)
Farmall F-30 belt pulley, $75 obo; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Farmall H, 1940, nice recent restoration. Good paint, new tires; Jim Farber 707-894-4759 eves (Yorkville CA)
Farmall M wide front in good shape, has been sitting for 5yrs, $1500; Mark Parker 541-619-2692 (Lebanon OR)
Farmall manifold, new, for A, Super A, B, C, Super C, 100 with C113 & C123 gas engines. List $143.16, sell $105.00. Contact for S/H costs; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall MD starter mower, runs good, $100; Larry Jacobson 801-254-3904 (So Jordan UT)
Farmall parts: Cub through M series, many parts available; Wendell Newman 775-882-8745 (Carson City NV)
Farmall Super A, 1952, restored, with 7 ft sickle mower, very good condition, $2500; Lee Burnett 208-610-5871 (Sandpoint ID)
Farmall Super A, runs good. Needs battery box and paint, $1600; Larry Jacobson 801-254-3904 (So Jordan UT)
Farmall Super MDV High Crop tractor. Rare find, has wide front, 3 point hitch, good tag, serial # E-30651J, tractor is complete and also comes with a Super MD tractor for parts as part of the package. Front axle has had some reinforcement strap welded on but it can be cut off. Ready for someone to restore, for a rare collector piece. Only 89 were built, not sure how many are left but not that many. If you want bragging rights to a truly rare tractor this is the one for you $15,000. Can line up transportation if needed, call if you have questions or need additional photos; Matt Grover 208-313-1615 (Rexburg ID)
Farmall/IHC PTO shaft, front. Box label shows 706-806-1206 & early 756-856-1256. 2009 Valu-Bilt catalog shows some 4 digit fits. Confirm w/ serial no. ReMan part no. 380261 (380261R1). 17 spline, 28 tooth. Lubed in plastic. 2009 Valu-Buit catalog shows: New List $141.21, Reman List $104.90. Sell for $75+ S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall/IHC PTO shaft, front. Box label shows fits for 1566 & 1568. Confirm w/ serial no. Part no. 67749. 18 spline, 26 tooth. Lubed in plastic. Has new appearance. Sell for $75 plus S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall/IHC PTO shaft, front. Box label shows late 756-856-1256 & early 766-826-966-1066-1456-1466-1468. Valu-Bilt catalog shows other 4 digit fits. Confirm w/ serial no. ReMan part no. 528676 (528676R1). 17 spline, 28 tooth. Lubed in plastic. 2009 Valu-Buit catalog shows: New List $141.21. Sell for $75+ S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Ferguson (early) used parts: Wheel weights (front & rear), Sherman rototiller gear (rear), steering boxes, hubs, axles, brake drums and engines. Too much to list; Walt Bain 541-218-4336/walterandsusanbain@msn.com (Grants Pass OR)
Ferguson High Clearance TO20, $1500; Chris Mielke 909-223-0858 (Norco CA)
Ferguson T0-20, 1950, runs real good, $1595; Al Norwood 760-347-6462 (Indio CA)
Ford (early) used parts: Wheel weights (front & rear), Sherman rototiller gear (rear), steering boxes, hubs, axles, brake drums and engines. Too much to list; Walt Bain 541-218-4336/walterandsusanbain@msn.com (Grants Pass OR)
Ford 2N, 1947, rebuilt engine, starter, generator, new air bath & exhaust, surface rust, needs paint & tires, don't miss this one! Good buy at $700; Lon Sisson 707-548-6399 or 707-829-8785 (Sebastopol CA)
Ford 2N, runs good, $1050; Dick Good 541-619-6090 (Tangent OR)
Ford 4110 orchard model, 1968, with 2600 original hours, ready to work, $4100 obo; Stu Wade 530-342-3114 or cell 530-521-0355 (Chico CA)
Ford 600, new paint, new tires, ps, very good running tractor, $1695; Al Norwood 760-347-6462 (Indio CA)
Ford 800, excellent condition, gone through, new engine, power steering, $4500 obo; Jerry Fischer 503-876-7921 (Willamina OR)
Ford 800, great condition, runs good, new tires, good metal, $3500; Terry Foutch 360-710-4848 (Port Orchard WA)
Ford 801 diesel, good tires, 3 pt, bad power steering, vertical shift transmission, $2100; Karl Klein 503-936-9714 (Rainier OR)
Ford 8N with hydraulic loader and mower, fresh paint, ready to go, $2950; Karl Klein 503-936-9714 (Rainier OR)
Ford 8N, runs and drives, moderate tires, new paint, hydraulic dump loader, comes with 5 ft mower and 3 ft tiller, $4000 package; Karl Klein 503-936-9714 or kleintractor@yahoo.com (Rainier OR)
Ford parts for 9N, 2N, 8N, sheet metal, engine parts, wheels; Al Norwood 760-347-6462 (Indio CA)
Ford tractor: WWII series Ford tractor on excellent steel front and rear and magneto start, plus a set of tip toe steel rears for same tractor or can use 8N centers, $2700; Norm Keesler 208-880-4323 or nmkeesler@clearwire.net (Nampa ID)
Funk conversion parts, engines adapters and frames for converting your N series tractor to a Funk conversion. Please call or email for parts and prices; Norm Keesler 208-880-4323 or nmkeesler@clearwire.net (Nampa ID)
International 1066 Farmall, for parts or as is, transmission problems, strong sounding engine, good 4-post canopy, poor tires. Offers expected on all or parts; Philip Wilson 530-342-7352 (Chico CA)
International 350 Hi-Utility gas, runs, 2000 hrs. Fast hitch 1 hyd. remote all lights $1750 obo; Mark Parker 541-619-2692 (Lebanon OR)
International 444 diesel, 1964, with low hours, bucket, fork lift, mower & rototiller attachment. Needs a little work, runs well, must sell, $2750 obo; Terry Foutch 360-710-4848 (Port Orchard WA)
International Harvester NOS 1-1/4" diesel starting carburetor, pn 251 413 R9D (TD 18?); Make offer or going to scrap; Wes Allen 530-751-1262 or almark@syix.com (Yuba City CA)
International hood side panels, side name plates, side radiator panels in assorted types and conditions: 806 LP, 660 Diesel, 300, 350, 400, 450, 544, 656, 856, 460, 560, 560 diesel, 504, 1256. Contact for availability, pricing; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
International T20 chassis parts, used, and one set of tracks; Bill Lamoureaux 360-398-1971 (Bellingham WA)
International TD14 with cable angle blade, winch, canopy. Complete tractor (does not run), $2500 or offer/trade for AC crawlers or parts? Mel Ford 707-485-8585 or mel@redwoodvalleygravel.com (Redwood Valley CA)
International TD6 motor parts block head; Mark Parker 541-619-2692 (Lebanon OR)
International TD9 grill/rock guard. Great shape, $75; Tim Bynum 530-436-2593 or timandlaura@snowcrest.net (Yreka CA)
International TD9 hood, with emblems. No dents, in good shape, $100; Tim Bynum 530-436-2593 or timandlaura@snowcrest.net (Yreka CA)
John Deere M. No serial number. Head and motor overhauled, carburetor rebuilt, excellent rear tires. Frame sanded and primed but tin needs restored. New muffler, belly mount, wheels restored. Hydraulic works but has not fired up yet. Forced sale due to health, $1,000; John Evers 503-623-8811 or 503-917-9318 cell (Dallas OR)
John Deere 4 front slab weights for New Generation tractors, $40 each or $125 for all; Mark Parker 541-619-2692 (Lebanon OR)
John Deere 40 crawler with blade, very nice condition, $4250; Dick Good 541-619-6090 (Tangent OR)
John Deere 40 Utility parts: running long block, front axle, transmission, hydraulic control, early style draw-bar, hood, early grill. Email with needs; Jake Winn 541-207-8327 or weasel2278@aol.com (Albany OR)
John Deere 40 Utility tractor. Clean, solid tractor. Good Tin. Runs good. Lights, 3pt, PTO, factory top link, $2750 obo. Can email pix; Jake Winn 541-207-8327 or weasel2278@aol.com (Albany OR)
John Deere 40c crawler, 1955, with large blade, good runner, hard worker. Unrestored condition, possibly industrial yellow from factory when new, has PTO in rear and radiator guard on front. Purchased from northern California where it was used mainly for snow removal. Pictures available upon request, $2000 obo; Jack Johnson 714-630 2912 or pd6pro@aol.com (Anaheim CA)
John Deere 440, 8ft blade, gas, reverser, steers good, $2950; Dick Good 541-619-6090 (Tangent OR)
John Deere 60 low seat standard, runs good, excellent sheet metal, many new parts, needs a new manifold and carb tune up, use it as is or great candidate for full restoration, only 1,900 made. $3500 or best offer, also have a BO for $3500 obo, would lower price to make a package deal; Tom Lewis 559-970-4781 or jdgreenla@aol.com (Fowler CA)