AA1150R side power takeoff assembly for John Deere BI tractor. Includes B880R First reduction gear cover and A1477R power takeoff with gear and lever. J. R. Hobbs estimates that probably less than ten of these units were produced, $3000. Email for photos; John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
Allis Chalmers B, 1939, good paint & rubber, runs good, $1000; Rich Dorn 951-532-5270 (Mira Loma CA)
Allis Chalmers B, 1941, good paint, good sheet metal, runs good, $795; Al Norwood 760-347-6462 (Indio CA)
Allis Chalmers B, 1952, sn B120609. Engine totally rebuilt new liners and pistons, turned crank, valve job including new exhaust seats. Clutch rebuilt, new release bearing, resurfaced flywheel. New water pump, rebuilt starter, rebuilt generator, 12 volt, new regulator, new solenoid. Sheet metal is straight, would love to be repainted. Front tires are like new, rear are very good. Hydraulic works. Rear blade and original front saddle weights included. Approximately 100 hours since rebuild runs like new, $2500; Jim Temple 541-935-7567(Noti OR)
Allis Chalmers bolt-on wheels for duals w/o tires. They came off of a D15 and should fit a D14 or D17 as well. They are in excellent shape, $50 obo; Stan Becktold 541-893-6754 (Richland OR)
Allis Chalmers CA, early 1950's. Tractor has been cosmetically restored. It is in working condition and runs well. Could benefit from some top end work if were to be used as field tractor. A local tractor enthusiast who works on them in his spare time restored this. He did a wonderful job. Asking $3000 or best offer. Please email me for pictures and more info; Clinton Paulson 585-410-2152 or capauls29@hotmail.com (Bath NY)
Allis Chalmers G, older restoration that runs good, good tin & tires, factory hydraulics with front & rear toolbar, rare front weight, $4200; John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
Allis Chalmers HD-5, dozer, canopy, winch, excellent, $4250; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers HD-7 farm cat with cab, 371 Detroit, $1500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers K, has blade, winch, canopy, restore? $2100; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chalmers W Road Patrol, good shape, rare, $5250; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Allis Chamers C, 1948, runs, needs battery, $1300; Rich Dorn 951-532-5270 (Mira Loma CA)
Allis-Chalmers WD, 1952. Mostly restored, new epoxy paint, tires 100%, 3-point hitch, lots of new or NOS parts. Rear dirt scoop, boom pole, rear blade. Used for show and plowing snow. Includes books and some extra parts. Fun to drive in parades. Can e-mail photos. $3,200; Tom Lyman 208-660-3089 or tomlyman@hotmail.com (Post Falls ID)
Baker valve for John Deere power lift, $275; Gary Jondle 360-379-8438 (Port Townsend WA)
Case 12-20 Crossmotor, 1920's, complete except mag & bad manifolds, stuck, $5000; Kenny Doyle 559-730-8409 (Exeter CA)
Case C, 1929 on steel, flat fan belt, restored, $3750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Case parts: Hood, grille & other Misc. sheet metal parts for some sort of Case "Tripl-Range" Tractor. Call for details; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Case RC, 1936, restored, new rubber, paint, $3750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Case S, 1944, wide front, running when parked, good sheet metal, tires leak air, electric start, tractor complete, $1,200; Dale Eisert 916-749-5210 (Loomis CA)
Caterpillar 10, 1929, running when parked, original side panels, good sheet metal, painted yellow, hydraulic blade, $4,150; Dale Eisert 916-749-5210 (Loomis CA)
Caterpillar 10, runs, steers good, has engine side panels, $3000; Bob Smythe 503-257-9615 (Rhododendron OR)
Caterpillar 10, two parts tractors, $650 each; Bob 503-257-9615 (Sandy OR)
Caterpillar 15 (small), 7C series, 1932. Excellent running condition, always stored under cover. Picture available, $7500; Melody Hemley 253-853-6438 or cell 360-801-1240 (Port Orchard WA)
Caterpillar 15, two parts tractors, $650 each; Bob 503-257-9615 (Sandy OR)
Caterpillar 20, Big 20, have two to restore, $3000 & $2000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 20/25/28 PTO complete, reduced to $350; Cat 20/25/28 radiator grill, $150; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 22 parts: belt pulleys, choice, both loose, complete, metal cast pulley or conventional, $500 each; Cat 22 Zenith K5 Propane carb complete with spare gas Zenith carb, $200; Cat 22 Zenith K5 carbs complete, two carbs, $175; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 22 wide gauge top seat with 8' 4 gang disc. Runs good with many new parts, $4000; Wally Adams 408-268-3308 (Morgan Hill CA)
Caterpillar 22, citrus orchard with Bishop fenders, $2500; Caterpillar 22 engine, very nice, $950; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 22, stuck, $700; Cat 22, rough, $700; Bob 503-257-9615 (Sandy OR)
Caterpillar 22, wide gauge running tractor. Pretty darn good undercarriage with rails that appear to be 75% or more with beefy sprockets. Grousers are 1.375 to 1.5". Still has original Cat decals viewable on hood and fuel tank. Modest hitch pin wear. Runs 20 psi oil pressure at idle. Think mag needs a rebuild as the tractor runs fine from idle to a bit over half throttle and as you provide more throttle (past half) the tractor starts sputtering. $2750. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30 on propane, will run with a little work. Tracks and undercarriage are in very good condition. S/N s9016, has belt pulley on rear. $2500 or offer. Can E-mail photos to serious buyers; Dax Kimmelshue 530-345-4456 or daxandkaren@yahoo.com (Durham CA)
Caterpillar 30G wide-gauge factory electric start. Tractor runs and drives very well. Tractor has rebuilt top end, great manifolds, rebuilt electric starter. CM4 magneto, lights, factory nose-guard, mushroom air-breather. Very straight tractor which is unrestored. Can provide pictures. $7500 Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30G-R4 brand new old stock exhaust manifold with fins. Fabulous shape. Indescribably good, $1500. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 30G-R4 intake manifold in very good shape (no drop tube), $450. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 35 diesel, bad final, otherwise good, $2750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 40 5G gas wide gauge, rare tractor, recent engine work, electric start, good undercarriage, runs & drives very well, new paint & seats, very nice, $9500. Check our web site www.omnitrac.com. Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar 40 diesel, 1935, sn 1725, rear BeGe Unit, 40% undercarriage, ran good when last used 3 years ago. Also Murray Hydraulic Carryall Model M86, $5000 for both, or will split; Larry Alvares 530-824-2693 (Corning CA)
Caterpillar 50, gas, complete, restorable, $5000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 5U wide gauge direct electric start large front idler toolbar dozer. Tractor runs and drives very well. Tractor had the top end gone through this winter with head shaved/trued, all new glow-plugs, All new injector nozzles, new gaskets, new thermostat, new main clutch. $2k in just new parts alone. New hydraulic hoses from factory metal lines to hydraulic rams. Factory PTO with belt pulley attachment. Belly pan (no hook). Tractor starts great hot or cold. Cat 44 single spool front mounted pump. Can provide more pictures. Extremely original. 158XX serial number. $10,000; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar 60, complete, with blade, runs good, $10000; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 60, have 2, make one, $6000 for both; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar 60, sn 4914, very good undercarriage, new rings & valve grind, new fenders, rebuilt vacuum tank, rebuilt carb & mag, ID tags are intact on the rear housing, drives excellent, $16000. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar cable control, rear model 29, sn 31E, all controls, 2 drive shafts, one from 46A, one from D7E, 2 engine adapters from D6, D7E, nice; Jerry Kirschling 360-951-9777 or grk_2@comcast.net (Rochester WA)
Caterpillar combine, early '30's, very restorable, $2500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D-2 5U, very nice, direct electric start, $6750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D2 belt pulley, $350; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar D2 J series: has four. One of the tractors are wide gauges and three are standard gauges. Four have the main engines loose. Asking $2500 for all five (actually 3.5 tractors) which is approaching scrap price but Rick is not a supporter of scrapping whole tractors and wants to sell to a party who may put one or more of the tractors to use in a restoration or as parts donors to another restoration; for details Rick Hawksworth 559-658-5711 or dunefrk@razzolink.com (Ahwahnee CA)
Caterpillar D-4 7J, restorable, $1500; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar D4 belt pulley, $350; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar D4 parts: draw bar $15; fender $10; grill guard $10; sprocket assembly $15; loader bucket $25; Ron Nevins 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar D4 parts: draw-bar $15, fender $10, grill guard $10, sprocket assembly $15, loader bucket $ 25; Ron Nevins 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar D6 seat tank $45. Good condition, photos available; Ron Nevins 530-474-3228 or hidcrk@yahoo.com (Shingletown CA)
Caterpillar D6, 1948, sn 8U806. Carco winch, canopy, blade. Running, working Cat, $3500; Chris Carl 425-218-1313 or jdnut@wavecable.com (Camano Island WA)
Caterpillar D8-14A starting motor trans; Jerry Kirschling 360-951-9777 or grk_2@comcast.net (Rochester WA)
Caterpillar D8-46A transmission, model #7M825, out of sn 9 to 10 series; Jerry Kirschling 360-951-9777 or 360-273-8389 or grk_2@comcast.net (Rochester WA)
Caterpillar pads: wide 24" conventional pads for D4/R4/30/28. Rails ok, not special. 64 pads total with tall grouser height and little wear. Slight pitting in some pads as these came from the south, $1500. Can provide pictures; Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar parts: 4S straight blade, complete with hydraulics off D47U, $2750. Canopy for D4, $750; Cat D47U four roller track rails, 95%, has pads, but pads only 50%, D4N winch, complete, very good, $1500; Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar parts: D8 draw bars off D7E and D8-14A; Cat 24 volt generator, belts, reversible fan from 46A, sn 33000; carb off pony motor; generator 6 volt; starter 12 volt for pony motor; Cat track grease gun (volume compressor), book #7H1680 large button fitting; Cat draw bar pin; Jerry Kirschling 360-951-9777 or 360-273-8389 (Rochester WA)
Caterpillar parts: package D2/R2 guards, hydraulics, belly pan; I am packaging an R2/D2 Belly pan with a tow hook on it with a D2 hard nose-guard AND two cat 44 hydraulic pumps, 2 sets of lines from the pump to the cross-over pipe, two sets of cross-over pipes (fender to fender), two diverter values, one D2 mounting bracket, and one D2 pump to harmonic balancer coupling shaft. I think the pumps will need to be rebuilt. One does not turn currently. More discrete pictures available of the various parts. $1400. Greg Andrade 510-427-8095 or dunefrk@razzolink.com (San Juan Bautista CA)
Caterpillar RD4, restorable, with tool bar blade, $1750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)
Caterpillar straight blade for D25U, complete with Cat hydraulics $2200. One after-market tilt angle blade, complete, for D25J or D25U series $1200. Check our web site www.omnitrac.com. Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar used parts for Cat 10, 15, 20, 22, 30, 40, 60, D2, D4, 2 Ton, D2, D4, JD Lindeman and JD crawlers, some TD6 and TD9 parts. Dozers, canopies, belly pans and winches. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar/Holt 2-ton sn 76028, good undercarriage, very straight, new paint & seats, original carb, drives very well, $6500. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Caterpillar: Large selection of antique caterpillar tractors Cat 10 thru 60, some restored, some ready to restore. Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Clamp-on 12X38 dual rims and all mounting hardware from JD 630 row crop no tires some surface rust lots of yellow paint please come get'em $100; Jim Temple 541-935-7567 (Noti OR)
Cletrac AG-6-H, good condition, runs good, $1450; Jim Chamberlin 530-823-2353 (Auburn CA
Cletrac F, rare little tractor, circa 1921. In same family for over 40 years, was displayed in a renowned museum for most of that time. It is missing the starting crank and air box. But I have been told both of these items are not that difficult to come by. I have not run it, but it is free and has compression. It was put into the collection running. Call or email for photos. Valued at $12,000 to $15,000 but first $10,000 takes her home; Rick Limpp 406-670-7399 or oscarspark@bresnan.net (Billings MT)
Cockshutt 30 Forklift as built for the Royal Canadian Air Force. Built in 1955 for Armament handling. Motor runs Ok, transmission slips out of second. Foot throttle, power steering, heavy front axle. New tires front, very good 13-26 on rear. All sheet metal complete and in good shape. Ag hitch added later, no PTO, no belt pulley. Here is your chance to own a piece of Canadian RCAF history, as this may be one of 15 made. Tractor located in Abbotsford, BC, $5500.; H Penner 306-783-0274 or tractorboy880@sasktel.net (Yorkton SASK)
Cockshutt 50, 1954, completely restored, including overhaul, new tires and paint. Beautiful tractor. Pictures available, $6,000; Bill Holt 360-273-2095 or holt273@comcast.net (Rochester WA)
Co-op No. 2, 1936, wide front sn 206, new front wheels, tires & tubes, tool box, good sheet metal, engine stuck, square fenders, belt pulley, $1,700; Co-op No. 2, 1936, wide front sn 413, running when parked, new front & rear tires & tubes, painted red, rare rear PTO, FAST, $2,250; Dale Eisert 916-749-5210 (Loomis CA)
Decals, NOS for Cub Cadet, Farmall, International, some Implements. Contact for needs, costs, S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
DuAll loader model 325 on 460 Farmall. Large bucket. W/O bucket cylinders or valve body. $500 obo; Dave Wattenbarger 208-267-7468 (Naples ID)
Ensign carb for Caterpillar 65 or 70, very clean & nice, $1200; Check our web site www.omnitrac.com; Dennis Wilkinson 541-568-4735 or dwilkinson@omnitrac.com (Cove OR)
Farmall 300, straight sheet metal, single front, torque converter, hydraulic front & back, PTO, draw bar, excellent running condition, $2000; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall 300. Good sheet metal, wide front, torque converter, 3 pt hydraulic hitch, hyd front & back. Very good running condition, just needs paint, $2500; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall C, single front, good tin, runs good, has hydraulics; Aubrey Greer 805-740-9379 (Lompoc CA)
Farmall Cub 1949, new rings, valves and bearings. Good tires and fresh IH paint, hydraulics $2,350 with model 193 mounted plow and 28-A mounted disc. $2,000 without implements; Russ Shorten 509-382-8925 or cell 509-876-1795 (Dayton WA) [link to photo]
Farmall Cub misc parts; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Farmall Cub, 1947, sold "as is" condition. Parts tractor or could be good runner with the right amount of work and time. 4-digit serial number 3154. Has no drawbar, generator, or front grille. Pictures available upon request, $600 obo; Jack Johnson 714-630 2912 or pd6pro@aol.com (Anaheim CA)
Farmall Cub, 1948, overhauled carb, gen, gov, mag, partial paint job, gas tank cleaned, new radiator. Need to assemble, $2,300; Dale Eisert 916-749-5210 (Loomis CA)
Farmall F-14 (124), restored. New rubber; Jim Farber 707-894-4759 eves (Yorkville CA)
Farmall F-20, complete, original parts, new rear tires. Runs but needs TLC and gas tank, $2500; Ed Bodily 775-623-2293 (Winnemucca NV)
Farmall F-30 belt pulley, $75 obo; Daniel Morgan 760-378-3448 or MorganDM95@aol.com (Onyx CA)
Farmall H, 1940, nice recent restoration. Good paint, new tires; Jim Farber 707-894-4759 eves (Yorkville CA)
Farmall manifold, new, for A, Super A, B, C, Super C, 100 with C113 & C123 gas engines. List $143.16, sell $105.00. Contact for S/H costs; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall MD starter mower, runs good, $100; Larry Jacobson 801-254-3904 (So Jordan UT)
Farmall Super A, 1950 era, runs good, straight sheet metal, with disc; Mike Collins 360-871-1474 (Port Orchard WA)
Farmall Super A, runs good. Needs battery box and paint, $1600; Larry Jacobson 801-254-3904 (So Jordan UT)
Farmall/IHC PTO shaft, front. Box label shows 706-806-1206 & early 756-856-1256. 2009 Valu-Bilt catalog shows some 4 digit fits. Confirm w/ serial no. ReMan part no. 380261 (380261R1). 17 spline, 28 tooth. Lubed in plastic. 2009 Valu-Buit catalog shows: New List $141.21, Reman List $104.90. Sell for $75+ S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall/IHC PTO shaft, front. Box label shows fits for 1566 & 1568. Confirm w/ serial no. Part no. 67749. 18 spline, 26 tooth. Lubed in plastic. Has new appearance. Sell for $75 plus S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Farmall/IHC PTO shaft, front. Box label shows late 756-856-1256 & early 766-826-966-1066-1456-1466-1468. Valu-Bilt catalog shows other 4 digit fits. Confirm w/ serial no. ReMan part no. 528676 (528676R1). 17 spline, 28 tooth. Lubed in plastic. 2009 Valu-Buit catalog shows: New List $141.21. Sell for $75+ S/H; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
Ferguson (early) used parts: Wheel weights (front & rear), Sherman rototiller gear (rear), steering boxes, hubs, axles, brake drums and engines. Too much to list; Walt Bain 541-218-4336/walterandsusanbain@msn.com (Grants Pass OR)
Ferguson T0-20, 1950, runs real good, $1595; Al Norwood 760-347-6462 (Indio CA)
Ford (early) used parts: Wheel weights (front & rear), Sherman rototiller gear (rear), steering boxes, hubs, axles, brake drums and engines. Too much to list; Walt Bain 541-218-4336/walterandsusanbain@msn.com (Grants Pass OR)
Ford 4110 orchard model, 1968, with 2600 original hours, ready to work, $4100 obo; Stu Wade 530-342-3114 or cell 530-521-0355 (Chico CA)
Ford 600, new paint, new tires, ps, very good running tractor, $1695; Al Norwood 760-347-6462 (Indio CA)
Ford 8N, runs and drives, moderate tires, new paint, hydraulic dump loader, comes with 5 ft mower and 3 ft tiller, $4000 package; Karl Klein 503-936-9714 or kleintractor@yahoo.com (Rainier OR)
Ford 800, great condition, runs good, new tires, good metal, $3500; Terry Foutch 360-710-4848 (Port Orchard WA)
Ford 9N, 1941, running when parked, good sheet metal, good tires, 3pt stuck in down position, new muffler, $2,200; Dale Eisert 916-749-5210 (Loomis CA)
Ford Funk Conversion, 1950. Flat Head 6cyl Ford engine. Howard transmission that works. Tractor runs. Ok front rubber, poor rear rubber. Great tractor for that Ford collection, $4000 obo; Jacob Hudson 425-577-9536 (Redmond WA)
Ford parts for 9N, 2N, 8N, sheet metal, engine parts, wheels; Al Norwood 760-347-6462 (Indio CA)
Ford tractor: WWII series Ford tractor on excellent steel front and rear and magneto start, plus a set of tip toe steel rears for same tractor or can use 8N centers, $2700; Norm Keesler 208-880-4323 or nmkeesler@clearwire.net (Nampa ID)
Funk conversion parts, engines adapters and frames for converting your N series tractor to a Funk conversion. Please call or email for parts and prices; Norm Keesler 208-880-4323 or nmkeesler@clearwire.net (Nampa ID)
IH Farmall 560, complete, runs great, sheet metal good condition, no 3 pt, $2000 obo; Doug D'Avis (509)750-2744 (Moses Lake WA)
International 444 diesel, 1964, with low hours, bucket, fork lift, mower & rototiller attachment. Needs a little work, runs well, must sell, $2750 obo; Terry Foutch 360-710-4848 (Port Orchard WA)
International Cub Lo-Boy, 1958. Very good condition. New wheels, rubber, seat, battery box, correct two-tone paint, front wheel weights, rimguard in rear tires, extra parts. Hydraulic fast hitch, with moldboard plow. Ready for work, fun or parades. Must sell, $2400; Bill Loder 425-788-6938 or 425-869-3861 or wloder1901@verizon.net (Carnation WA) [link to photo]
International hood side panels, side name plates, side radiator panels in assorted types and conditions: 806 LP, 660 Diesel, 300, 350, 400, 450, 544, 656, 856, 460, 560, 560 diesel, 504, 1256. Contact for availability, pricing; Jim Robinett 206-713-3441 or tractrmnul@aol.com (Ontario OR)
International T-340 with 6-way dozer, runs good, needs pins and bushings, $1800; Jim Chamberlin 530-823-2353 (Auburn CA)
International TD14 with cable angle blade, winch, canopy. Complete tractor (does not run), $2500 or offer/trade for AC crawlers or parts? Mel Ford 707-485-8585 or mel@redwoodvalleygravel.com (Redwood Valley CA)
John Deer M. No serial number. Head and motor overhauled, carburetor rebuilt, excellent rear tires. Frame sanded and primed but tin needs restored. New muffler, belly mount, wheels restored. Hydraulic works but has not fired up yet. Forced sale due to health, $1,000; John Evers 503-623-8811 or 503-917-9318 cell (Dallas OR)
John Deere 40 crawler, 3-roller, street pads, rear hyd, no blade, runs & works good, good tine, $3,000; Charles Insley 775-553-9932 (Doyle CA)
John Deere 40 cylinder head (#M-1768T), also will fit M, reconditioned by local machine shop, $250; Larry Schwarz 360-736-6442 or larrystp@yahoo.com (Centralia WA)
John Deere 40 Utility parts: running long block, front axle, transmission, hydraulic control, early style draw-bar, hood, early grill. Email with needs; Jake Winn 541-207-8327 or weasel2278@aol.com (Albany OR)
John Deere 40 Utility tractor. Clean, solid tractor. Good Tin. Runs good. Lights, 3pt, PTO, factory top link, $2750 obo. Can email pix.; Jake Winn 541-207-8327 or weasel2278@aol.com (Albany OR)
John Deere 40c crawler, 1955, with large blade, good runner, hard worker. Unrestored condition, possibly industrial yellow from factory when new, has PTO in rear and radiator guard on front. Purchased from northern California where it was used mainly for snow removal. Pictures available upon request, $2000 obo; Jack Johnson 714-630 2912 or pd6pro@aol.com (Anaheim CA)
John Deere 40-C with original 3 roller frame (1 of 600), original Yakima blade, recent clutch and brake work, runs and drives excellent, sheet metal fair, $3480 obo/trade; Karl Klein 503-936-9714 or Kleintractor@yahoo.com (Rainier OR)
John Deere 60 low seat standard, runs good, excellent sheet metal, many new parts, needs a new manifold and carb tune up, use it as is or great candidate for full restoration, only 1,900 made. $3500 or best offer, also have a BO for $3500 obo, would lower price to make a package deal; Tom Lewis 559-970-4781 or jdgreenla@aol.com (Fowler CA)
John Deere A parts: parts off 1946 and 1948 A's. Some engine parts, sheet metal, radiator. Email me with needs; Jake Winn 541-207-8327 or weasel2278@aol.com (Albany OR)
John Deere A, 1937, unstyled rear round spoke wheels, needs restored, $1000; Kurt Spegel 503-648-9052 (Cornelius OR)
John Deere A, 1937, with wide front, unstyled tractor with California dealer conversion to wide front (not factory), cut off wheels, older poor restoration, poor tires, runs and operates well, pretty much complete tractor. Pictures available by email; Bob Gauntt 360-892-3733 or unstyledl@yahoo.com (Vancouver WA)
John Deere A, 1950, Schwartz WF, building collapsed on tractor, runs great, hood smashed, $750 obo; Chris Carl 425-218-1313 or jdnut@wavecable.com (Camano Island WA)
John Deere AN, 1937 unstyled, one of 591 built, quite complete but needs restoration, has factory round spoke rear wheels, reduced to $4500. Email for photos. John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
John Deere AN, 1950 42" rears, with 16" single front. Running tractor, sheet metal is ugly, $1000 obo; Chris Carl 425-218-1313 or jdnut@wavecable.com (Camano Island WA)
John Deere AN, 1950, 42" rears with 16" single front. Motor is loose, tractor is complete, $1000 obo; Chris Carl 425-218-1313 or jdnut@wavecable.com (Camano Island WA)
John Deere ANH, 1947 on 40" spokes, good tires, rarest of the styled A's, only 236 made. Mostly complete, needs restoration, $8900. Email for photos; John Boehm 530-668-9410 or ratractor-fs@yahoo.com (Woodland CA)
John Deere AO, 1947, electric start, runs good, restorable, $3750; Don Chappell 503-397-0152 or cell 503-679-2726 or janc@ados.net (St Helens OR)